Engineering Portal Access

Restricted Access: This portal provides advanced vehicle configuration and firmware management capabilities.
Invalid credentials. Please try again.
Back to User Portal
Password Change Required
You must change your password before continuing.

This is required for first-time login or after your password has been reset by an administrator.

Must be at least 8 characters and different from current password
Beep Off Engineering
PLATFORM MANAGER USERS AUDIT LOG INFO USER PORTAL Disconnected
Connection Status
Click "Connect" to establish Bluetooth connection with Beep Off.
Hazard Light Status
Unknown
Ignition Status
Unknown
Security Notice: Turn on your vehicle's hazard lights first. Bluetooth is only visible when hazards are active for security. Alternatively, press the emergency programming button.
Platform Management
Use Platform Manager to Create Configurations

All vehicle platforms are now managed through the Platform Manager - a visual editor for creating and editing platform configurations without uploading files.

Open Platform Manager
Software Creation Tool
Create New Release

Loading platforms from Platform Manager...

Published Releases
Loading releases...
Firmware Management (OTA)
Process Arduino ZIP
Format: X.XX (e.g., 3.16)
Upload the compiled .zip from Arduino IDE
If checked, firmware will be available for over-the-air updates

Download Firmware
Flash package includes bootloader, partitions, and firmware for UART programming.
Available Firmware Versions
Version Size Uploaded By Status Actions
Loading firmware...
Device Management
Serial Number Credits Unlimited Current Platform Last Configured Actions
Loading devices...
Showing 0 devices
Device OTA Testing
Device Connection
Connect to a device to test firmware updates.
Serial: -
Firmware: -
Hardware: -
WiFi Settings
Firmware Update
Connect a device to check for updates
0%
Starting...
Configuration
Choose your vehicle manufacturer.
Choose your vehicle platform from available releases.
Selected:
Safety Features Control
Turn OFF to disable this feature
Turn OFF to disable this feature
Turn OFF to disable this feature
Turn OFF to disable this feature
Turn OFF to disable this feature
Toggle ON to keep features enabled. Toggle OFF to disable features when ignition starts.
Device Information
Serial Number
Not Connected
Firmware Version
Not Connected

Monitoring Status
Ignition
Off
Hazard Lights
Not Detected
CAN Bus Statistics
CAN Bus 1 (I/O)
0
Messages
CAN Bus 2 (I/O)
0
Messages
CAN Bus 3 (I/O)
0
Messages
0
Filtered Messages
Inactive
Bus Activity
0
Total Messages
CAN Message Filtering
Filter Rules
Active Rules:
No custom filter rules defined
Filter Options
Shows detailed information about which filter rules match incoming messages
Tip: Use the "Custom CAN Messages" section below to test your filter rules with specific message patterns.
Custom CAN Messages
Send Custom Message
Enter CAN ID in hexadecimal format (without 0x prefix)
Enter data bytes separated by spaces (max 8 bytes)
Select which CAN bus to send the message to
Message Recording
Choose which bus to record messages from
BLE PIN Calculator
Device Lost PIN? Paste the serial number to calculate the BLE pairing PIN.
Just paste as-is: Enter BEEP-1234567890ABCDEF or 1234567890ABCDEF - the calculator automatically removes the prefix and pads with leading zeros.
Paste the full serial number (with or without "BEEP-" prefix) - automatic formatting applied.
Calculated PIN
------
6-digit BLE pairing code

WARNINGS:
  • Do Not Distribute: Never share this calculator code, export it, or make it publicly accessible
  • Misuse: All PIN calculations are logged. Misuse of this tool will result in termination of your account.
Device Control
CAN Bus Loopback Test
Hardware Setup: Connect a wire between CAN1-H and CAN2-H, and another between CAN1-L and CAN2-L (or CAN3). This test sends a message on CAN1 and verifies it's received on CAN2 and CAN3.
Test Results:
Bus Operation Status
Error

An error occurred.

Platform Upload

Are you sure you want to upload this platform?

Device Details
Loading device details...
Configuration History
Loading configuration history...
Register New Device

Enter the device serial number to register it for API access. The serial number is displayed on the device's serial monitor during boot.

Must be at least 5 characters (letters, numbers, hyphens only)